Hot STM Labs

Adsorption of TiCl4 and initial stages of Ti growth on Si(001)

 

Adsorption of TiCl4 and Ti growth on Si(001) were investigated over a range of temperatures by scanning tunneling microscopy. At 300 K, intact TiCl4, Ti and Cl, and mobile TiCl2 are identified on the Si surface. At higher temperatures, deposition initially produces two-dimensional Ti islands, and continued deposition produces three-dimensional clusters. Above 630 K, both Si and Ti islands and Si/Ti clusters are formed.However, cluster growth is limited by Cl passivation of Si and Ti surfaces below 950 K. Above 950 K, the tops of partially submerged titanium silicide crystals are observed.

___________________________________________

 

Figure 1. A sequence of STM images showing adsorption of TiCl4 on a Si(001) surface at 300 K. (a) A bare surface before the dose,(b) after the dose, TiCl4, Ti and Cl are observed. (c) Twenty seconds later, TiCl4 has dissociated into TiCl2 and 2Cl. The sample bias voltage is –2.0 V.

 

We identify TiCl4, TiCl2, Ti, and Cl on the clean Si(001) surface by analyzing STM images before and after several instances of dosing surfaces with a fraction of a monolayer of TiCl4.

 

 

 Typical images are shown in Figure 1.  The same area of a 300 K Si(001) surface is imaged before (1a) and after (1b) exposure to 0.05 L of TiCl4, and again 20-seconds later (1c).  The arrows in Figs. 1b and 1c highlight four different adsorption features observed. 

 

Ti and Cl are identified by comparing our STM images at various biases (not shown) with previous STM studies of PVD of Ti on Si (001)[i] and the chemisorption of Cl and CH3Cl on Si(001)at room temperature.[ii]  Cl adsorbs singly on individual substrate atoms; usually 2 Cl atoms adsorb on adjacent Si atoms.  All three types of Cl adsorption features identified by Boland are observed.12,[1]  Figure 1b shows that the Ti has adsorbed on a pedestal site near a single dimer vacancy between two neighboring Si dimers in the same row.  At a –2.0 V sample bias, a single adsorbed Ti atom appears as a 0.6 ±0.1 Å high protrusion with a diameter of 8 ± 0.5 Å.

 

 The two other adsorption features cannot be identified with either Ti or Cl. Conversions between these and Ti and Cl features allow their identification as intact TiCl4 and the fragment TiCl2.  Over a period of a few minutes, TiCl2, Ti, and Cl replace the initial density of TiCl4.  Through successive images, we see TiCl4 disappear, leaving 2 Cl and a white streak along a substrate row.  In every instance investigated (around 30) the creation of a streak is simultaneous with that of a pair of Cl atoms on the same or an adjacent substrate row.  A streak is produced by a mobile species moving slightly faster than the STM scan rate.[iii]  An example of such a conversion can be seen in fig’s 1b and 1c.  In fig. 1b, taken immediately after a dose, two features are labeled TiCl4.  Figure 1c shows that, twenty seconds later, 2 Cl’s and a white streak along the same dimer row have replaced one of these features.  On four occasions individual streaks have been observed to transform into a single Ti atom and 2 Cl atoms near a defect.  Thus, we identify the streaks with mobile TiCl2 molecules and propose the following decomposition path:

 

 
 
TiCl4(gas) ®  TiCl4(adsorbed) ® TiCl2(mobile at 300K) + 2Cl(adsorbed)  

                                             TiCl2 (mobile at 300K) ® Ti(adsorbed near defect) + 2Cl(adsorbed)

 

        

 

 




OurSTM observations agree with those from Medicino et al.’s LED, TPD, and AES work in that all the constituents of TiCl4 are adsorbed on the Si(001) surface.4  However, it appears that the complete decomposition of TiCl4 at room temperature is a very slow process.  Even after a 2 min anneal to 450 K some TiCl2 remains intact, trapped by defects.  It is also at this point that small one-dimensional Ti islands first appear.11  Neither islands nor clusters form at room temperature.


B.  450 K

 
 


Figure 2. A sequence of STM images of a Si(001) surface at 475 K.  (a) After an initial exposure to TiCl4 (0.2 L).  Ti forms one-dimensional islands.  Cl adsorption produces dark surface regions.  (b) After a second dose of TiCl4 (0.4L), 90% of surface is covered by Ti and Cl.  The arrow indicates a mobile Ti atom on an island. The gray scale in the inset has been exaggerated to assist identification of the different surface features:  white is a Ti atom, light gray is bare Si surface, dark gray is Cl covered surface, and black is a surface vacancy. (c) After a 1-minute interval, ripening is observed.  A typical cluster has a height of 2.7 Å.  (d) After a further dose of TiCl4 (0.9 L).  The sticking probability has decreased from unity.  The number of 4.2 Å clusters increases by a factor of three.  The sample bias voltage is –1.6 V.

 


The sequence of STM images in Fig. 2 shows the initial stages of Ti growth on a Si(001) surface at 450 K after exposure to TiCl4.  The STM images reveal that TiCl4 decomposition is complete and that at a low coverage (0.2 ML of Ti) Ti initially exists on the surface individually or in rows perpendicular to the Si dimer rows, as seen in Fig. 2a.  The bright Ti adsorption features show no preference for locations near step edges or vacancies.  They are in a ratio of approximately 1 to 2.2 ± 0.2 with the dim Si dimers in the surface that are identified with pairs of Cl atom,[1] i.e., the ratio of Ti atoms to Cl atoms is approximately 1 to 4.  This indicates complete adsorption.  Consistent with the work of Ishiyama et al.,11 a negligible amount of Ti diffuses beneath the surface at 450 K.[2]

 

Once the chemisorbed layer covers more than 90% of surface, successive dosing of the surface with 0.2 L of TiCl4 induces the ripening of Ti clusters.  At this temperature Ti atoms are mobile, but move slowly relative to the STM imaging time.  Therefore, analysis of STM movies allows us to follow island and cluster formation atom-by-atom.  When rows capture mobile Ti atoms, they evolve into 3D clusters.  See, for example, the row indicated by the arrow in the STM image of Figs. 2b.  After a one-minute interval, it has transformed into a cluster indicated by the arrow in Fig. 2c.  With a sample bias of -1.6 V, the initial clusters appear 2.7 ± 0.4 Å high.  Our STM movies show that these clusters are mobile until they grow to 4.2 ± 0.4 Å high by absorbing more Ti atoms.  The observation of cluster formation and growth indicates that the smaller clusters are composed of 4 or 5 atoms while the larger ones are composed of 6 or 7 atoms.  We believe that the initial transformation from Ti row to cluster is due to the breaking of Si-Ti bonds in favor of the stronger Ti-Ti bonds.  Initially, 4 or 5 Ti atoms form a cluster that is not stable.  However, by capturing more Ti and bringing the number of atoms up to 6 or 7, a stable cluster is formed.  The bonding conditions at the interface between Si substrate and Ti clusters are not known. 

 

The sticking probability for TiCl4 on highly covered Si (001) surfaces decreases from unity (at low coverage) as surface coverage increases.  After 90% of the Si surface has been covered, doses yield roughly 30% the deposition they did on the bare surface.  Taking the sticking probability to be unity for the bare surface, this indicates an 0.3 sticking probability for the 90% covered surface.  After continued dosing, no more deposition is observed; the sticking probability falls to zero, and the growth of Ti clusters ends.[i]  This is due to the passivation of the Si surface by Cl.  The Cl terminates the dangling and weak p bonds of the Si surface12 and the Ti clusters, leaving no sites for further growth and Ti clusters.  Titanium growth on Si and on Ti clusters can be restarted after tip induced Cl desorption.14

C.  630 K

 
 

 

Figure 3.  An STM image showing both Si and Ti islands on a Si(001) surface at 630 K.  The sample bias voltage is -2.5V.

 

100Å

 

Figure 3 shows the Si, Ti, and Si/Ti islands and clusters present on a 630 K Si(001) surface that has been dosed with 0.1 L of TiCl4. The Si islands are identified by image comparison with Si PVD on Si(001) studies and images of roughly annealed bare Si(001).[ii]  At this temperature, two mechanisms can supply the Si ad-atoms incorporated in these features.  Silicon atoms along the step edges can escape onto the terraces,15 and Si atoms in the terrace surfaces can be ejected and replaced by Ti atoms.[iii]  After the dose, only half of the expected Ti was observed; assuming that the sticking probability is roughly the same as on the 450 K surface, the other half of the Ti atoms must have sunk into the Si substrate by this process.  Once on the terraces, Si and Ti are mobile at 630 K, and can meet to form the observed features. 16,13  A uniform fuzziness observed in the images may be due to the presence of highly mobile Cl.

 

Analyzing the islands and clusters, a few observations can be made.  These features often abut surface defects, suggesting that the defects may influence the seeding or limiting of growth.  Also, image series reveal that these features are stable, in spite of a measured rate of Ti diffusion into the surface near 4 Hz at this temperature.11  This indicates that the diffusion barrier is increased either by island formation or possibly by the presence of Cl on the surface.  The average cluster height is 6 ± 0.4 Å.

 

D.  970 K

Previous work has determined some of the details of Ti CVD from TiCl4 at high temperatures.  In LEED, TPD, and AES studies, Medicino and Seebauer concluded that Cl-free material is difficult to grow using TiCl4 below 950 K.4  However, Hocine and Mathiot found that, above 950 K, Ti diffuses rapidly into the Si,[iv] thus making the precursor better suited for silicide than for thin film growth.   Indeed, Briggs et al. have recently used STM and Transmission Electron Microscopy (TEM) to investigate titanium silicide produced by a TiCl4 dose and an anneal to 1200 K.9  Additionally, it is known that Cl etches the Si(001) surface and produces SiCl2 gas above 800 K;  during the etching processes, ragged step edges, pits, and 2D islands form on the Si(001) surface.[v]

 


Figure 4. STM images obtained after exposing a Si (001) surface at 970K to TiCl4.  (a) A TiSi2 structure surrounded by a characteristic Cl etched surface.  (b) A close-up of the edge of the structure reveals a trough circling it.  The sample bias voltage is –2.1 V.

As expected, after exposure to 1.5L of TiCl4 at 970 K, the surface has the ragged appearance characteristic of Cl-etched Si(001)18 and is populated with structures such as that in Fig. 4.  These cover approximately 3% of the surface.  Focusing on the edge of the structure shows that it grows into the Si substrate, as is seen in Fig. 4b.  Immediately surrounding it, there is a trough, more than 5 atomic layers (6.8Å) deep.  This results from Si being gathered into the structure during its formation.  The well-defined geometry of these structures indicates that they are crystalline.  Indeed, we expect titanium silicide crystal formation at this temperature.  Theory predicts that the most likely equilibrium stochiometry is TiSi2 in the C49 structure,[vi] and recently Briggs et al. verified this for samples exposed to either pure Ti or TiCl4 and well annealed at 1200 K.9  The structures seen in that work display the same geometries and surrounding troughs as those seen here.  While the visible height of the structure in Fig. 4b is 14 ± 0.5 Å, TEM images reveal that the TiSi2 crystals in Brigg’s work extend “like icebergs” deep below the surface with widths only a few times greater than their depths.9  A further 2L dose of TiCl4 doubles the number of titanium silicide structures and the average visible height of TiSi2 grows up to 20Å, while the step edge recession is more than 7 atomic layers (9.5Å).

 

IV.  CONCLUSIONS

 

At 300 K, we observe intact TiCl4 and mobile TiCl2 as well as Ti and Cl atoms on Si(001).  Initially TiCl4 dissociates into TiCl2 and 2 Cl atoms.  Next, some of the TiCl2 dissociates near vacancies into Ti and 2 Cl atoms.  However, the complete decomposition is slow at this temperature.  For deposition at 450 K, we observe 2D Ti island growth followed by Ti clustering.  Dosing at 630 K, conglomerate islands and clusters of Ti and Si form.  At 970 K, just above the Cl-free temperature, Cl etches the surface and partially submerged TiSi2 crystals are formed locally. 



[1] The slight deviation from the expected ratio of 1 to 2 is likely due to the difficulty in distinguishing Cl pair features from surface defects.

[2] The observation of roughly 400 Ti atoms for 10 min. yields only 4 candidates for Ti diffusion beneath the surface.  This suggests a rate of less than 1.5 × 10-5 Hz.



[i] T. Mitsui, R. Curtis, and E. Ganz, J. Appl. Phys. 86, 1676 (1999).

[ii]  C. Pearson, M. Krueger, R. Curtis, B. Borovsky, X. Shi, and E. Ganz,  J. Vac. Sci. Technol. A 13, 1506 (1995).

[iii]  K. Miwa and A. Fukumoto,  Phys. Rev. B 52, 14748 (1995); B. D. Yu, Y. Miyamoto, O. Sugino, T. Sakai, and T. Ohno,  Phys. Rev. B 58, 3549 (1998).

[iv]  S. Hocine and D. Mathiot,  Mater. Sci. Forum 38-41, 725 (1989).

[v]  M. Chander, D. A. Goetsch, C. A. Aldao, and J. H. Weaver,  Phys. Rev. B 52, 8288 (1995); K. Nakayama, C. A. Aldao, and J. H. Weaver,  Phys. Rev. B 59, 15893 (1999); G. A. deWijs, A. DeVita, and A. Selloni,  Phys. Rev. Lett. 78, 4877 (1997).

[vi]  X. Wallart, J. P. Nys, and G. Dalmai,  Appl. Surf. Sci. 38, 49 (1989); X. Wallart, J. P. Nys, H. S. Zeng, G. Dalmai, I. Lefebore, and M. Lannoo,  Phys. Rev. B 41, 3087 (1990); H. Jeon and R. J. Nemanich,  Thin Solid Films 184, 357 (1990); B. D. Yu, Y. Miyamoto, O. Sugino, T. Sasaki, and T. Ohno,  Appl. Phys. Lett. 72, 1176 (1998).


[1] Cl appears either individually or in pairs, oriented either parallel or perpendicular to the substrate dimer rows.  Though Cl pairs resemble common surface defects, they may be distinguished at low sample biases.  Also, continuous patches of Cl pairs display dim dimer rows parallel to the surface rows where as patches of dimer vacancies reveal the perpendicular rows of the next Si layer down.  



[i]  K. Ishiyama, Y. Taga, and A. Ichimiya,  Phys. Rev. B 51, 2380 (1995); K. Ishiyama, Y. Taga, and A. Ichimiya,  Surf. Sci. 349, 267 (1996); K. Ishiyama, Y. Taga, and A. Ichimiya,  Surf. Sci. 357-358, 28 (1996).

[ii]  J. J. Boland,  Science 262, 1703 (1993); M. J. Bronikowski and R. J. Hamers,  J. Vac. Sci. Technol. A 13, 777 (1995).

[iii] M. Krueger, B. Borovsky, and E. Ganz, Surf. Sci. 385, 146 (1997).